Waste drilling mud is one of the main pollution sources in the petroleum and natural gas industry. The Oilfield D rilling W aste M ud T reatment P rocess is to treat the waste drilling mud (drill cuttings) immediately while drilling to meet the requir
Harmless Treatment Process of Waste Drilling Mud While Drilling Read More »
The M ud Zero Discharge S ystem developed by KOSUN mainly includes shale shaker, centrifuges, cuttings dryers, and screw conveyors. After processing, it can reach an oil content about 2-5%, which is in line with national and industry standards. After dewatering centrifuge separation and multifunctional purification unit, the harmful part of the mud is discharged with the solid phase. The liquid phase can be used to prepare the mud, discharge as wastewater or irrigate, and the solid part is solidified and then landfilled. On-site centralized processing while drilling, using physical centrifugal separation technology to recover most of the base oil on-site, reducing the oil content and total amount of waste (the solid phase oil content of the spin dryer is 2%-12%, and the solid phase oil con
Introduction to the advantages of KOSUN’s Mud Zero Discharge System Read More »
Vacuum deaerator is a new type of special equipment used to process gas intrusion drilling fluid, also called negative pressure deaerator, which can quickly remove various gases invaded into drilling fluid, restore the specific gravity of mud and stabilize mud performance, havinga very important role. At the same time, it can also be used as a high-power mud agitator, suitable for all kinds of mud circulation purification systems. This equipment is a negative pressure deaerator with a scientific and reasonable design structure, which can effectively separate gas and liquid, filter out impurities, and ensure that the exhaust pipe is always unblocked. The drilling fluid vacuum deaerator , usually installed after the drilling fluid shale shaker, can effectively separate harmful gases in the d
New type of special equipment for processing gas intrusion drilling fluid Read More »
The drilling industry strictly follows the environmental protection law and regulations regarding waste disposal, and clearly states that the arbitrary discharge of drilling waste is strictly restricted. So how to deal with waste during the drilling process? KOSUN actively responds to the national call to provide professional solutions for drilling waste treatment ! KOSUN drilling waste treatment system includes: drying shaker, screw pump, environmentally friendly centrifuge, screw conveyor, and other solids control equipment that can be used for mud drying treatment. We know that in the process of oil exploration and production, a lot of waste will be left on the well site. These wastes are stored in the sewage pond of the well site. If the drilling waste is not treated thoroughly, it may
Drilling waste treatment process and treatment effect Read More »
In shield construction, waste mud is comprehensively treated by mud solidification, filter press, centrifugation and other treatment methods, and waste mud is treated with zero discharge and pollution-free treatment, so as to achieve zero waste slurry discharge in the shield construction process. As an environmentally-friendly engineering auxiliary equipment, the E nvironmental P rotection M ud P urification Equipment is increasingly used in non-excavation foundation construction such as mud wall protection technology, pile foundation construction, and shield construction. The E nvironmental P rotection M ud P urification Equipment not only enables solid-liquid separation of waste slurry, but also greatly saves mud treatment costs during construction, reduces construction costs, reduces en
New Environmental Protection Mud Purification Equipment Read More »
In the low temperature environment, in order to promote the normal operation of the drilling rig, while ensuring that it has a heating system, it should also be treated with normal heat preservation. Only when the normal heating performance is ensured and the heat preservation treatment is carried out, the drilling rig can work normally under low temperature conditions, and its maintenance cost can also be reduced. According to the analysis of the current actual situation, the heat preservation treatment of the low-temperature solids control system is mainly to build a heat preservation shed, and use the heat preservation shed for heat preservation. KOSUN has many years of industry experience in the field of petroleum solids control. It is a professional solids control equipment manufactur
What are the insulation methods for the drilling low-temperature solids control system? Read More »
he land-based skid-mounted oil-based mud treatment system for oil and gas fields manufactured by KOSUN
Skid-mounted Oil-based Mud Treatment System Read More »
KOSUN is a professional oil-based mud treatment equipment manufacturer. KOSUN can customize efficient and economical drilling oil-based mud treatment equipment for customers according to the customers project site conditions. After the oil-based waste
Customize and Economical Oil-based Mud Treatment Equipment Read More »
Countrys continuous development of drilling business has promoted the gradual expansion of our countrys drilling scope and fields. However, there are still many problems in some relatively special areas. Common special areas include: high-cold areas,
Why develop a low-temperature drilling mud circulation system? Read More »
